PetroleumSeismology.com

Home » Images » 51 «Prev Next»

Exploring the sub-basalt

Chapter 1 - Introduction to Petroleum Seismology

Voluminous basaltic basins (white ellipses) along the margins of the Altantic Ocean.

A significant number of hydrocarbon reserves are located below voluminous complex volcanic rock formations or sandwiched between two such volcanic rock formations. Most of these volcanic rock formations are basaltic, and the sedimentary layers located beneath them are broadly termed as sub-basalts. The offshore Atlantic Ocean area, for example, contains a number of hydrocarbon reserves in the sub-basalt formations. Some of these basins are currently the target of active oil and gas exploration, e.g., the basins on the Faroes, West Greenland, Brazil, Angola, and Namibia margins, as well as basins off mid-Norway. This figure shows voluminous basaltic complexes identified along prospective rifted continental margins. Notice that these basins stretch to very deep waters, in some cases to more than 2,000 m. Petroleum explorationists and producers working in these areas are faced with significant data- acquisition,processing and interpretation challenges, and huge drilling risks due to the depth of the water column and to the presence of voluminous complex volcanic rocks located above these basins. (Adapted from Coffin and Eldholm, 1992.)

Other Images in 51

View Comments on this Image

An example of the sailing path of a marine vessel in a towed-streamer survey

Images - Chapter 8 An example of the sailing path of a marine vessel in a towed-streamer survey. Note that the time for turning from one sailing line to another is about nine hours for vessels carrying streamers that are 10 km long. The dotted line indicates the turning legs of the sailing path.

This figure illustrates a typical sailing path of a 3D survey; the vessel travels back and forth, shooting and collecting data along many parallel lines, resulting in seismic data generated along lines 25 to 50 meters apart. Note that it takes about nine hours to turn from one sailing line to another for a vessel carrying 10-km-long streamers. Today, data are recorded even when the vessel is turning.

A shot diagram

Images - Chapter 7 A display of source and receiver distribution of a 2D seismic line in the so-called shot diagram. The rows corresponding to common-shot gathers and columns to common-receiver gathers. The diagonal is the zero-offset section, and all the other lines parallel to the diagonal are common-offset gathers (also known as common-offset sections). The lines perpendicular to the diagonal are the CMP gathers.

Another illustration of towed streamer acquisition

Images - Chapter 7 Another illustration of towed streamer acquisition

Interference noise

Images - Chapter 7 An illustration of interference noise in seismic data before and after. This figure shows the stack of seismic interference noise contaminated shots from another line in the Gulf of Mexico. Interference noise is clearly visible. Attenuation of seismic interference noise can be achieved by the use f-x prediction filters. Courtesy of Western Geco.

Other examples of structural traps

Images - Chapter 1 Structural traps. (A) Tilted fault blocks in an extensional regime. The seals are overlying mudstones and cross-fault juxtaposition against mudstones. (B) Rollover anticline on thrust. Petroleum accumulations may occur on both the hanging wall and the footwall. The hanging wall accumulation is dependent on a subthrust fault seal, whereas at least part of the hanging wall trap is likely to be a simple, four-way, dip-closed structure. (C) Lateral seal of a trap against a salt diapir and compactional drape trap over the diapir crest. (D) Diapiric mudstone associated trap with lateral seal against mud wall. Diapiric mud associated traps share many common features with that of salt. In this diagram, the diapiric mud wall developed at the core of a compressional fold. (E) Compactional drape over a basement block commonly creates enormous low-relief traps. (F) Gravity-generated trapping commonly occurs in deltaic sequences. Sediment loading causes gravity-driven failure and produces convex-down (listric) faults. The hanging wall of the fault rotates, creating space for sediment accumulation adjacent to the fault planes. The marker beds (grey) illustrate the form of the structure that has many favourable sites for petroleum accumulation. Adapted from Gluyas JG and Swarbrick RE (2003) Petroleum Geoscience. Oxford: Blackwell Science.