PetroleumSeismology.com

Home » Images » Chapter 1 » 44 Next»

Structural traps

Chapter 1 - Introduction to Petroleum Seismology

Sketch cross-sections of different types of faults. (a) Reversed fault caused by crustal compression. (b) Normal fault produced by crustal tension (note that for both traps to be sealed, the fault planes must be impermeable). (c) Growth fault. "H" indicates hydrocarbon accumulations.

Commercial accumulations of petroleum are found in sedimentary rocks where subsurface geometries are able to stop the upward migration of petroleum. Such subsurface geometries are known as petroleum traps. They can be classified in three groups: (i) structural traps, which are caused by folding or faulting, (ii) diapiric traps, which are caused by density differences, and (iii) stratigraphic traps, which are caused by sedimentation or erosion. This figure illustrates examples of structural traps due to faulting; the three main types of fault traps are illustrated in this figure. Note that an essential requirement for a commercial accumulation of petroleum is the occurrence of an impermeable cap rock (also known as a seal) which inhibits the upward movement of petroleum. In the examples of petroleum traps in this figure, the fault plane is the impermeable seal. (Adapted from Selley, 1983.)

Other Images in Chapter 1

View Comments on this Image

An example of the sailing path of a marine vessel in a towed-streamer survey

Images - Chapter 8 An example of the sailing path of a marine vessel in a towed-streamer survey. Note that the time for turning from one sailing line to another is about nine hours for vessels carrying streamers that are 10 km long. The dotted line indicates the turning legs of the sailing path.

This figure illustrates a typical sailing path of a 3D survey; the vessel travels back and forth, shooting and collecting data along many parallel lines, resulting in seismic data generated along lines 25 to 50 meters apart. Note that it takes about nine hours to turn from one sailing line to another for a vessel carrying 10-km-long streamers. Today, data are recorded even when the vessel is turning.

A shot diagram

Images - Chapter 7 A display of source and receiver distribution of a 2D seismic line in the so-called shot diagram. The rows corresponding to common-shot gathers and columns to common-receiver gathers. The diagonal is the zero-offset section, and all the other lines parallel to the diagonal are common-offset gathers (also known as common-offset sections). The lines perpendicular to the diagonal are the CMP gathers.

Another illustration of towed streamer acquisition

Images - Chapter 7 Another illustration of towed streamer acquisition

Interference noise

Images - Chapter 7 An illustration of interference noise in seismic data before and after. This figure shows the stack of seismic interference noise contaminated shots from another line in the Gulf of Mexico. Interference noise is clearly visible. Attenuation of seismic interference noise can be achieved by the use f-x prediction filters. Courtesy of Western Geco.

Other examples of structural traps

Images - Chapter 1 Structural traps. (A) Tilted fault blocks in an extensional regime. The seals are overlying mudstones and cross-fault juxtaposition against mudstones. (B) Rollover anticline on thrust. Petroleum accumulations may occur on both the hanging wall and the footwall. The hanging wall accumulation is dependent on a subthrust fault seal, whereas at least part of the hanging wall trap is likely to be a simple, four-way, dip-closed structure. (C) Lateral seal of a trap against a salt diapir and compactional drape trap over the diapir crest. (D) Diapiric mudstone associated trap with lateral seal against mud wall. Diapiric mud associated traps share many common features with that of salt. In this diagram, the diapiric mud wall developed at the core of a compressional fold. (E) Compactional drape over a basement block commonly creates enormous low-relief traps. (F) Gravity-generated trapping commonly occurs in deltaic sequences. Sediment loading causes gravity-driven failure and produces convex-down (listric) faults. The hanging wall of the fault rotates, creating space for sediment accumulation adjacent to the fault planes. The marker beds (grey) illustrate the form of the structure that has many favourable sites for petroleum accumulation. Adapted from Gluyas JG and Swarbrick RE (2003) Petroleum Geoscience. Oxford: Blackwell Science.