PetroleumSeismology.com
Home » Images » Chapter 3 » 113 «Prev Next»

Possible refraction (head-wave) paths

Chapter 3 - Introduction to Petroleum Seismology

Possible refraction (head-wave) paths from the source to the receiver for incident P- and S-wave. The top half-space has velocities VP1, and VS1, and the bottom half-space has velocities VP2, and VS2. Notice that if VP1 > VS2, the modes P1S2S1 and P1S2P1 are not possible.

Refracted waves (also known as head waves) occur after the critical angle. As the elastic case that we have just described includes several possibilities of critical angles, several head waves are possible at the interface of two half-spaces. This figure shows the raypaths of four possible head waves for the case of an incident P-wave. These head waves are also illustrated in the snapshot plots in this figure. We can see that there are five possible head waves with an incident P-wave. Actually, five head waves is the maximum possible number for an incident P-wave; four are in the upper medium, one in the lower medium. This maximum number of five head waves is possible only if VP2 > VS2 > VP1 > VS1.

Other Images in Chapter 3

View Comments on this Image

An example of the sailing path of a marine vessel in a towed-streamer survey

Images - Chapter 8 An example of the sailing path of a marine vessel in a towed-streamer survey. Note that the time for turning from one sailing line to another is about nine hours for vessels carrying streamers that are 10 km long. The dotted line indicates the turning legs of the sailing path.

This figure illustrates a typical sailing path of a 3D survey; the vessel travels back and forth, shooting and collecting data along many parallel lines, resulting in seismic data generated along lines 25 to 50 meters apart. Note that it takes about nine hours to turn from one sailing line to another for a vessel carrying 10-km-long streamers. Today, data are recorded even when the vessel is turning.

A shot diagram

Images - Chapter 7 A display of source and receiver distribution of a 2D seismic line in the so-called shot diagram. The rows corresponding to common-shot gathers and columns to common-receiver gathers. The diagonal is the zero-offset section, and all the other lines parallel to the diagonal are common-offset gathers (also known as common-offset sections). The lines perpendicular to the diagonal are the CMP gathers.

Another illustration of towed streamer acquisition

Images - Chapter 7 Another illustration of towed streamer acquisition

Interference noise

Images - Chapter 7 An illustration of interference noise in seismic data before and after. This figure shows the stack of seismic interference noise contaminated shots from another line in the Gulf of Mexico. Interference noise is clearly visible. Attenuation of seismic interference noise can be achieved by the use f-x prediction filters. Courtesy of Western Geco.

Other examples of structural traps

Images - Chapter 1 Structural traps. (A) Tilted fault blocks in an extensional regime. The seals are overlying mudstones and cross-fault juxtaposition against mudstones. (B) Rollover anticline on thrust. Petroleum accumulations may occur on both the hanging wall and the footwall. The hanging wall accumulation is dependent on a subthrust fault seal, whereas at least part of the hanging wall trap is likely to be a simple, four-way, dip-closed structure. (C) Lateral seal of a trap against a salt diapir and compactional drape trap over the diapir crest. (D) Diapiric mudstone associated trap with lateral seal against mud wall. Diapiric mud associated traps share many common features with that of salt. In this diagram, the diapiric mud wall developed at the core of a compressional fold. (E) Compactional drape over a basement block commonly creates enormous low-relief traps. (F) Gravity-generated trapping commonly occurs in deltaic sequences. Sediment loading causes gravity-driven failure and produces convex-down (listric) faults. The hanging wall of the fault rotates, creating space for sediment accumulation adjacent to the fault planes. The marker beds (grey) illustrate the form of the structure that has many favourable sites for petroleum accumulation. Adapted from Gluyas JG and Swarbrick RE (2003) Petroleum Geoscience. Oxford: Blackwell Science.