f-k dip filtering
Chapter 8 - Introduction to Petroleum Seismologyf-k dip filtering for multiple attenuation.
F-k dip filtering can help discriminate against multiples on the basis of moveout. This figure shows this f-k filtering procedure. The data are transformed from the t-x domain to the f-k domain. F-k dip filtering distinguishes between primary and multiple reflections based on residual moveout after NMO corrections have been applied. Multiple events are flattened, with approximately no residual moveout, whereas the primary events will have some residual moveout. The data with NMO corrections are transformed in the f-k domain, in which primary and multiple events are now well separated based on their dips
(or equivalently apparent velocities). The zero dip corresponds to multiples which can be zeroed out. The following steps consist of performing the inverse Fourier transform and removing the NMO correction. We can see that f-k dip filtering can be effective for multiple removal, especially in the far offsets, but can leave multiples in the near offsets, where the moveout is minimal.
Other Images in Chapter 8
View Comments on this Image
An example of the sailing path of a marine vessel in a towed-streamer survey
Images - Chapter 8
An example of the sailing path of a marine vessel in a towed-streamer survey. Note that the time for turning from one sailing line to another is about nine hours for vessels carrying streamers that are 10 km long. The dotted line indicates the turning legs of the sailing path.
This figure illustrates a typical sailing path of a 3D survey; the vessel travels back and forth, shooting and collecting data along many parallel lines, resulting in seismic data generated along lines 25 to 50 meters apart. Note that it takes about nine hours to turn from one sailing line to another for a vessel carrying 10-km-long streamers. Today, data are recorded even when the vessel is turning.
A shot diagram
Images - Chapter 7 A display of source and receiver distribution of a 2D seismic line in the so-called shot diagram. The rows corresponding to common-shot gathers and columns to common-receiver gathers. The diagonal is the zero-offset section, and all the other lines parallel to the diagonal are common-offset gathers (also known as common-offset sections). The lines perpendicular to the diagonal are the CMP gathers.
Another illustration of towed streamer acquisition
Images - Chapter 7 Another illustration of towed streamer acquisition
Interference noise
Images - Chapter 7 An illustration of interference noise in seismic data before and after. This figure shows the stack of seismic interference noise contaminated shots from another line in the Gulf of Mexico. Interference noise is clearly visible. Attenuation of seismic interference noise can be achieved by the use f-x prediction filters. Courtesy of Western Geco.
Other examples of structural traps
Images - Chapter 1 Structural traps. (A) Tilted fault blocks in an extensional regime. The seals are overlying mudstones and cross-fault juxtaposition against mudstones. (B) Rollover anticline on thrust. Petroleum accumulations may occur on both the hanging wall and the footwall. The hanging wall accumulation is dependent on a subthrust fault seal, whereas at least part of the hanging wall trap is likely to be a simple, four-way, dip-closed structure. (C) Lateral seal of a trap against a salt diapir and compactional drape trap over the diapir crest. (D) Diapiric mudstone associated trap with lateral seal against mud wall. Diapiric mud associated traps share many common features with that of salt. In this diagram, the diapiric mud wall developed at the core of a compressional fold. (E) Compactional drape over a basement block commonly creates enormous low-relief traps. (F) Gravity-generated trapping commonly occurs in deltaic sequences. Sediment loading causes gravity-driven failure and produces convex-down (listric) faults. The hanging wall of the fault rotates, creating space for sediment accumulation adjacent to the fault planes. The marker beds (grey) illustrate the form of the structure that has many favourable sites for petroleum accumulation. Adapted from Gluyas JG and Swarbrick RE (2003) Petroleum Geoscience. Oxford: Blackwell Science.
- Home |
- Images |
- Drawings |
- Animations |
- Thoughts |
- Questions |
- Codes |
- Register |
- Privacy Policy
